Tools/Maintenance

We went through extra steps to make this tool half precision measuring instrument and half pry bar. - Tolerances as tight as a quarter of a thousandth of an inch (.0063mm) in some critical dimensions of this tool. - Ability to lock in the feeler so you don't have to second-guess your measurement after bumping it on the tire. - Top half of tool will rotate out of the way of fender stays and frame tubes. - Feeler gauge stick stores inside the top half of the tool, very handy for the traveling mechanic. - T-bolt extends past the tool for access to those problematic hangers found on some modern full suspension bikes. - Compact at just under 11" ( 28cm) - Re-buildable - While ideally your HAG should be sent back for a rebuild, it is possible to do them in the field by replacing the brass bushing in the T-Bolt. - Compatible with the three most common wheel sizes (26, 27.5/650B, and 700/29)

With thru axles becoming more and more common, the original Crombie tool was due for a makeover. We took the piloting pin and plus-sized it to work with the 12mm thru axle fitment that is actually standardized. We make this version as a dual-sided tool with two S Group ends, one for thru axle wheels and the other for regular hubs. The regular side has a hole deep enough to hide a skewer nut; it's really the best of both worlds. - Comes with a solid handle - Note: this version of the Crombie tool is not compatible with any Campagnolo wheels. - Dimensions: 9.625in x 1.0in

Service kit for Cane Creek suspension forks.

Service tools to ensure long-term success of Chris King hubs. - For intensive servicing of Ringdrive system found in most Chris King rear hubs - Included: Hub Cone Adjusting Tool, Cog Spline Wrench, Spline Driver, Driveshell Bushing Tool, and Service Manual - Does not fit R-45 model hubs. See TL7829 for proper tool fitting R-45 hubs

Do you like the Micro Pro/Pill tool, but need extra storage and Megaplug capability? Then this is the tool for you! Larger than a Pill but easily fits in the palm of your hand. Get one today to tackle the largest punctures and keep the ride going! Kit includes: x1, Megapill tool (dimensions: 2.59" x 1.11") x2, Megaplug repair plugs x5, Brass soft nose tip repair plugs x2, Megaplug insertion tubes x5, Standard insertion tubes x1 Micro Knife, and a pipe cleaner

Finish Line's Wax Lubricant is a unique formulation that features DuPont's Krytox, a highly advanced, thermally stable lubricant. Its specialized paraffin waxes set up dry and hard to repel grit and grime so your drivetrain runs silky-smooth and stays clean. Another nice feature is that, as parts get dirty, the wax layers can shed, which helps keep the chain and components cleaner.

- One-way Torque Wrench - 5-25 N'm. for 1/4" and 3/8 drive sockets - 21~105N·m, for 3/8" & 1/2" drive sockets

- Tap Pro set w/handle & pouch for - 3m X 0.5 dropout alignment screws - 5m x 0.8 water bottle, fender eyelets - 6m x 1.0 anti-brake large fender bracket - 10m x 1, derailleur hanger - 1/2 x 20tpi left & right pedal taps - 9/16 x 20 tpi left and right pedal taps

- Pre-calibrated torsion ratchet tool - Constructed with machined aluminum - Removable handle for easy storage in molded EVA case - Includes: 2.5, 3, 4, 5mm hex bits and T20, T25 Torx bits

Precision brake bleeding tools and adaptor kits for Magura brake systems. - Bleed adaptors fit MT series - Attaches to caliper only

Precision brake bleeding tools and adaptor kits for Magura brake systems.

Precision brake bleeding tools and adaptor kits for Magura brake systems. - 30mL graduations

- Featuring all five Muc-Off brushes in a handy storage bag - Claw brush ideal for chain, cassette and sprocket - Detailing brush ideal for tight areas such as suspension mounts or fork crowns - Soft washing brush ideal for your bike frame and wheels - Wheel and component brush ideal to clean rim and spokes with ease - Two-prong brush ideal to reach hard-to-shift dirt on your components

- Advanced fluor-polymer polish and protectant - Removes imperfections and fills minor scratches - 3 wax blend for long lasting, ultra deep shine - Clear coat safe, no powdery white residue

Forged with Chrome Vanadium (CR-v) steel, precision ground, heat-treated, plated and polished. The PAW-6 opens to 24mm and features a laser engraved measurement scale and dipped blue handle for comfort.

Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.

The Park Tool FR-5.2GT is designed specifically for use when removing and installing cassette lockrings from thru axle hubs. -Utilizes a 12mm guide pin to stabilize the tool during use - Fits 12-spline cassette lockrings from Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and others (23.5mm diameter) - Fits some Shimano and similar disc brake rotor lockrings

Park Tool's SW-11 is a forged, double-ended spoke wrench designed to fit select Campagnolo wheels. Precision machined, plated and vinyl dipped for comfort and long life. It fits Campagnolo 5.5mm and 6.0mm hex spoke nipples.

Use as a self-contained grease gun by using the included canister or screw the pump on to any tube of Park Tool grease, anti-seize or assembly compound. Small tip opening ensures precise placement of lube in any application.

After pressing the special connecting rivet into a Campagnolo 11-Speed Chain and breaking off the pilot, Campagnolo requires the end of the connecting rivet to be "peened" or "deformed" to prevent chain failure. The precision-machined CT-11 is used to accurately perform this critical process. Note: The CT-11 will not install or remove chain rivets. Its sole function is to peen and secure the end of the Campagnolo 11-speed connecting rivet. The Park Tool CT-4.2 Master Chain Tool (or previous model CT-4, each sold separately) is used for rivet installation and removal.

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 24mm wrench fits Shimano 15mm through-axle front hubs and many suspension-fork top caps. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Park's Shop Cone Wrenches are made of durable tool steel and are thin to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Park's special Y-heads put more material where it's needed for excellent durability and holding power. The 26mm size fits through-axle end caps and suspension fork crowns. Most applications require at least 2 cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.

The Team Race Stand is a Euro-style stand that securely holds your bike without clamping the frame tubes or seatpost but by holding it by either the front or rear dropouts via quick releases. It's ideal for bikes with ultra-light frame tubes and seatposts, and for bikes with tight access areas that can't be clamped. For easy wrenching this stand rotates horizontally 360 degrees and can be adjusted up and down from 28 to 38 inches (bottom bracket to the ground). This great stand was originally designed for the mechanics of the pro peloton, and is now available to home mechanics everywhere. Plus, the stand folds down to 33-inches long, so you can easily throw it in the back of your car.

Pure's Bike Wash is the easy way to bring the sparkle and shine back to the paintwork and polished metal parts of your beloved bicycle, and protect it too. It’s 100% acid-free so it's completely safe for all types of paint and finishes. Yet it has the power of acid-based cleaners to remove dirt and grime and leave a brilliant finish you'll love.

- 200 HOUR/1 YEAR SERVICE KIT (INCLUDES DUST SEALS, FOAM RINGS, O-RING SEALS, CHGR2 DAMPER SEALHEAD, DEBONAIR (SILVER) SEALHEAD—ZEB SELECT+/ULTIMATE A1 (2021)

- 4-in-1 cable cutter - Cuts cables and housing - Crimps cable ends - Crimps housing end caps - Housing end reformer in the handle TB-4575

Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.

- Replacement head sections for hammer 100 - 33mm diameter - Powerful hammering with surface protection - -01 : Semi-hard Urethane - -02: Hard Cellidor - -03: Very hard Nylon

- Practical rack for wall mounting. - Provides tidy storage for the screwdrivers. - Compatible with all Srewdrivers.

- Tire Lever Set (3 pcs) - Zinc-plated steel