Tools/Maintenance

Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.

Replacement shaft for Micro Bearing Press - 1/4" shaft diameter - 12" length

The soft face on the Titanium Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Titanium Hammer.

Replacement pins, these are original equipment chain pins for our chain tool, they also work as an alternate to the Campagnolo UT-CN300 11spd chain tool, Shimano CN-34 and CN-32 Sold in pairs.

Replacement feeler gauge for the Abbey Hanger Alligment Gauge Tool.

For use with 1/4" Micro Bearing Press Shaft

The soft face on the Shop Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Shop Hammer.

For use with 1/2" Micro Bearing Press Shaft

Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.

1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.

This tool makes dust wiper installation an easy task. The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.

The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise. The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts. Compatibility: - Chain ring lockrings on Shimano 12spd mountain crank sets. - XT and Ultegra bottom brackets

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

We listened to your requests and created a socket style Crombie tool that is compatible with ratchets and torque wrenches. The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. Compatible with all Campagnolo cassettes.

The Crombie tool is a game changer when it comes to swapping cassettes. Whether you're a professional mechanic swapping cassettes several times a day or a DIY kind of guy, this gem has a place on your tool bench. The first time a quick release spring rolls under your bench the Crombie tool paid for itself. If you like to remove the cassette for a detailed cleaning or just swapping from one cassette to another, it's a big time saver and a breeze to use. This version of the tool has a Shimano/SRAM remover on one side with a Campagnolo on the other. A precision machined spline ensures maximum engagement and durability. The STANDARD version comes with a solid handle which gives the tool some mass making it the preferred choice in the shop. The SUPER LIGHT version shaves 125 grams out of the handle. SL handles are plenty durable for lockrings that are torqued close to the 40 NM spec. If you commonly come across over torque lockrings get the standard handle!

With thru axles becoming more and more common, the original Crombie tool was due for a makeover. We took the piloting pin and plus-sized it to work with the 12mm thru axle fitment that is actually standardized. We make this version as a dual-sided tool with two S Group ends, one for thru axle wheels and the other for regular hubs. The regular side has a hole deep enough to hide a skewer nut; it's really the best of both worlds. This SUPER LIGHT version has a hollow handle to save weight for the traveling mechanic. SL handles are plenty durable for lockrings that are torqued close to the 40 NM spec. - Note, this version of the Crombie tool is not compatible with any Campagnolo wheels. - Dimensions: 9.625in x 1.0in

The Charger 2 wrench is designed for use on the lower seal head of Charger 2 and Charger LT dampers. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your suspension fork when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

The Reverb is an advanced and complicated component and service becomes a breeze with this speciality wrench. Designed for use on the inner seal head and upper collet of both 30.9 and 31.6 millimeter version of the Reverb dropper post. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your seastpost when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

Many athletes are fortunate enough to be able to ride nearly anything. For those that are sensitive to bike fit though, replicating fit to a new bike or confirming fit after travel can be a challenge involving lots of trial and error. This set of tools allows accurate and repeatable measurements for saddle height, angle and setback. The accuracy and repeatable measurements also serve as a base to make adjustments to fit. -The magnetic saddle height bullets ensure you get an accurate center at the BB by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate. -Two reference marks on the saddle plate means you can pull a measurement to the exact same spot relative to the nose of the saddle every time. This gives you accuracy down to a single millimeter. -The front of the saddle plate is engraved with a ruler, to allow you to calculate saddle setback at the saddle. This allows you to drop the plumb bob off the side of the bike and clear all of the bottle cages. -The wide plate has ample room to mount a level, protractor or smart phone for adjusting the angle of the saddle. This is particularly helpful for non traditional saddles like SMP and Adamo.

Two years in the making, this chain tool is built to stand the test of time. The threaded body and lead screw are made from cro-moly and receive a low friction powder vapor deposition (PVD) coating to give it a silky feel you've never felt in a chain tool before. Large handles ensure ease of use with any chain. The freely rotating pin is made from a shock rated tool steel and will likely last as long as the rest of the tool. The chain tool comes with a spare chain pin in the handle and they are cross-compatible with Shimano and Campagnolo pins. The greatest part of the chain tool has to be the interchangeable mid plate. The saddled part that holds the chain in position can be swapped to work with nearly anything the industry comes out with. This ensures that your investment won't become obsolete when company "X" comes out with an 18-speed cassette in 20 years. The tool also peens Campagnolo 11 and 12 speed chains to factory specs using a backstop that threads into the backside of the tool as a stop. Compatible with 9-12 speed chain, including the new 12-speed chains from Campagnolo and Shimano's XTR 9100.

This is an add-on kit for the popular Abbey Bike Tools Modular bearing press, adding even more versatility for the modern mechanic to deal with all the different shapes, sizes, and styles. The kit includes drifts for all common bearing sizes with a bearing inner diameter (ID) of 15mm or larger. Includes the over-axle drifts required to install bearings in DT, Zipp, and other modern captured bearing hubs. These drifts feature a 1/2" (12.7mm) ID and can be used with other presses if need be. Drifts included with this set precisely fit the following bearing sizes: - 6702 - 6703 - 6704 - 6803 - 6804 - 6902 - 6903 - 6904 - 17287 - 15267/15268