Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands

Tools

$2.00
Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.
$24.00
Replacement shaft for Micro Bearing Press - 1/4" shaft diameter - 12" length
$25.00
The soft face on the Titanium Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Titanium Hammer.
$30.00
Replacement pins, these are original equipment chain pins for our chain tool, they also work as an alternate to the Campagnolo UT-CN300 11spd chain tool, Shimano CN-34 and CN-32 Sold in pairs.
$30.00
For use with 1/4" Micro Bearing Press Shaft
$30.50
The soft face on the Shop Hammer is destined to be gouged, get worn down, or even melt (if you leave it near heat). Replacement soft face for Abbey Shop Hammer.
$45.00
For use with 1/2" Micro Bearing Press Shaft
$45.00
Replacement 6/8mm Hex bit for both the Abbey BBQ Wood Handled Pedal Wrench and the Team Issue Pedal Wrench.
$45.50
The magnetic saddle height bullet ensures you get an accurate center at the bottom bracket by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate.
$45.50
The magnetic saddle height bullet ensures you get an accurate center at the bottom bracket by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate.
$59.50
1/8" mid plate, needed to use the Decade chain tool with wide 1/8" track and single speed chains.
$59.50
For use with the Decade Chain Tool this AXS Mid Plate is required for the SRAM AXS Road and the new MTB Transmission Flat Top chains. This part is not needed for other 12spd chains from various manufacturers. The mid plate is visually differentiated from the other Decade mid plates by three dots on the face of the plate.
$75.50
This is a 13mm socket made specifically for the bleeders on modern Fox forks. These bleeders are built just like a top cap, with minimal height of the hex drive. So it's a perfect application for our original chamferless sockets. Use these to install the fenders that mount behind the bleeders or when servicing your fork. Socket uses a 3/8" square drive. Compatibility: Fox fork models 36,38 and 40 equipped with bleeders.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. Drivers are made in diameters specific to stanchion sizes for most modern forks including 32, 34, 35, 36, 38, and 40mm. The Fork Seal Press is built with modern tight fitting fork seals in mind. Using a common handle with a stainless steel striking surface to give excellent durability when setting seals with a mallet. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time. *** Note, these drivers are designed to be used with our handle, hitting them directly with a hammer can cause failure and will not be covered under warranty.
$78.00
This tool makes dust wiper installation an easy task. The Fork Seal Press is built with modern tight fitting fork seals in mind. The handle provides ample clearance for your hand around the fork crown while allowing a good grip to seat the seal. The Delrin drivers are built to use the upper fork bushing as a guide. Making sure the seal goes in square the first time, every time.
$89.50
This dedicated socket is built to engage all 4 of the holes on a SRAM dub crank arm dust cap. These caps don't normally need to be removed but when you do need to work with them, few things work well. These tools feature a common 3/8" square drive like the rest of our socket range and also have a hexagonal exterior so you can mount them in a vise and use the crank arm as the lever if so desired. The sockets are also marked for the left hand thread (clockwise to loosen) this part uses. Compatible with all SRAM dub cranks, road/mountain/gravel.
$91.00
This simple tool is designed to remove and install the static bearing in the shock ends of many modern rear shocks. Machined from durable stainless steel this compact tool allows the user to remove and install the DU bushings without resorting to hammers and punches. The coarse acme thread keeps the constant turning to a minimum.
$105.00
The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise. The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts. Compatibility: - Chain ring lockrings on Shimano 12spd mountain crank sets. - XT and Ultegra bottom brackets
$115.50
The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.
$115.50
The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.
$115.50
The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.
$115.50
The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket.
$115.50
The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.
$144.00
We listened to your requests and created a socket style Crombie tool that is compatible with ratchets and torque wrenches. The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. Compatible with all Campagnolo cassettes.
$157.00
With thru axles becoming more and more common, the original Crombie tool was due for a makeover. We took the piloting pin and plus-sized it to work with the 12mm thru axle fitment that is actually standardized. We make this version as a dual-sided tool with two S Group ends, one for thru axle wheels and the other for regular hubs. The regular side has a hole deep enough to hide a skewer nut; it's really the best of both worlds. This SUPER LIGHT version has a hollow handle to save weight for the traveling mechanic. SL handles are plenty durable for lockrings that are torqued close to the 40 NM spec. - Note, this version of the Crombie tool is not compatible with any Campagnolo wheels. - Dimensions: 9.625in x 1.0in
Page 1 of 2 Next page